Bike Computer Spoke Magnet: How to Install and Calibrate It Right
Learn how to mount a bike computer spoke magnet, align it with the sensor, and set wheel size so your speed and distance readings stay accurate.
Updated November 2026
A bike computer spoke magnet is the small magnet clipped to a spoke that lets your speed sensor count wheel rotations. Get the magnet position, sensor gap and wheel size right, and your speed and distance readings will be accurate. This guide walks through the setup, the checks and the common errors that cause erratic numbers.
What the Spoke Magnet Does
Most wired and many wireless speed sensors use a reed switch or Hall-effect sensor mounted on the fork or chainstay. Each time the magnet passes the sensor, the computer registers one wheel revolution. Speed comes from how quickly those pulses arrive, and distance comes from the total count multiplied by your programmed wheel circumference. If the magnet is loose, misaligned or too far from the sensor, pulses get missed or doubled, and the readings drift.
Shopping for one? See our guide: Bike Computer vs Watch (2026): Which Is Better for Cycling?. If you want more background, see Best 10 Bike GPS Computers for Bike Touring Navigation.
Installing the Magnet and Sensor
- Choose a spoke on the non-drive side of the rear wheel, or either side of the front wheel. Avoid spokes near the brake caliper or rim.
- Clip the magnet onto the spoke so its face points toward the sensor’s path. Most magnets have a flat side that should face outward.
- Mount the sensor on the fork leg or chainstay, usually with a zip tie or rubber strap. Keep it on the side the magnet will pass.
- Spin the wheel slowly by hand and watch the gap. The manufacturer typically specifies a maximum gap, often a few millimeters. Tighten the sensor so the magnet passes within that range without touching.
- Make sure the sensor is parallel to the magnet’s path, not angled, so the magnet stays in its detection zone through the full rotation.
Calibrating Wheel Size and Testing
Once the hardware is secure, set the wheel circumference in the computer. Many units offer a wheel-size table by tire size, but measuring is more reliable. Mark the tire on the ground, roll the bike one full revolution, and mark again. Measure the distance in millimeters and enter that value. A 700x25c road tire typically measures close to 2100 mm, but your actual number depends on tire pressure and load.
To test, ride a known distance, such as a marked stretch of road or a route you have mapped, and compare the computer’s distance with the known figure. If the number is consistently off by the same percentage, adjust the circumference accordingly.
Common Mistakes
- Mounting the magnet too far from the sensor, causing missed pulses at speed.
- Letting the magnet rub the sensor or the frame, which can wear the magnet or break the sensor.
- Using the wrong wheel size after switching tires, which skews every distance figure.
- Placing the magnet on a spoke that flexes or loosens under braking, shifting its position.
- Forgetting to recheck alignment after a wheel is removed or trued.
Recommended Gear
- Cateye speed sensor kit: Many riders replace the stock magnet and sensor with a matched kit when the originals wear out or get lost. View on Amazon
- Spare spoke magnets: Keeping one spare on hand makes a roadside repair quick if a magnet falls off. View on Amazon
FAQ
Can I use a spoke magnet with any bike computer?
Not always. Check whether your computer uses a magnet-based (reed or Hall) sensor, since some newer units use accelerometers or GPS-based speed instead. Your computer’s manual will list the compatible sensor type.
Why does my speed jump around?
The most common cause is a loose magnet or a sensor gap that is too large. Tighten the magnet, realign the sensor and test again.
Where should I put the magnet on a disc-brake wheel?
Choose a spoke well away from the rotor and caliper. Make sure the magnet clears the brake pads and that the sensor is mounted so it cannot contact the rotor.
Conclusion
A properly placed spoke magnet, a tight sensor gap and an accurate wheel circumference are all you need for reliable speed and distance data. Recheck the setup after tire changes or wheel service. For model-specific steps, consult your computer’s manual.
Related reading
- iGPSport Bike Computer Review (2026): Which Model Should You Choose?
- What Is Cadence on a Bike Computer? A Beginner's Guide
- What Bike Computer Does Jonas Vingegaard Use? Garmin vs Wahoo Compared
Ready to choose one?
