We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Measure Head for Bike Helmet: A Step-by-Step Sizing Guide

Learn how to measure head for bike helmet with a soft tape, find your correct size in centimeters, and check fit before every ride.

Updated November 2026

Learning how to measure head for bike helmet sizing takes about two minutes and a flexible tape. You will find your head circumference, match it to the manufacturer’s size chart, and confirm the helmet sits level and snug. Getting this right matters more than brand or color, because a helmet that is too loose can shift on impact and one that is too tight causes pressure and distraction.

Gather the Right Tools

You need a soft, flexible measuring tape, the kind used for sewing or body measurements. A rigid metal tape will not follow the curve of your skull accurately. Have a pen and paper ready, and note your result in centimeters, since most helmet size charts use metric units.

Shopping for one? See our guide: 6 Best Full Face MTB Bike Helmets for Downhill and Enduro (2026).

How to Measure Your Head Circumference

  1. Stand in front of a mirror and keep your head level, with your eyes looking straight ahead.
  2. Wrap the tape around your head about one inch (2.5 cm) above your eyebrows and just above your ears.
  3. Keep the tape level all the way around. It should sit at the widest part of your head, usually at the back.
  4. Keep the tape snug but not tight. It should not compress your hair or skin.
  5. Read the measurement where the tape overlaps and record it in centimeters.
  6. Repeat the measurement two more times. If the readings differ by more than a few millimeters, take the average.

Match Your Measurement to the Size Chart

Helmet sizes are not standardized across brands. A medium from one manufacturer may fit differently than a medium from another, so always use the chart published by the brand you are considering. Manufacturers typically list a size range for each helmet, such as a medium covering a specific centimeter band.

Typical Size Label Head Circumference Range (Manufacturer Dependent)
Small (S) Lower band of the brand’s chart
Medium (M) Middle band of the brand’s chart
Large (L) Upper band of the brand’s chart

If your measurement falls between two sizes, check the brand’s fit notes. Some owners report that a helmet with an adjustable retention system handles borderline measurements better than one with a fixed fit. For a deeper look at larger heads, see Bike Helmet Large Head: How to Find a Proper Fit (Step-by-Step).

Check the Fit on the Helmet

A measurement only gets you close. Once the helmet arrives, confirm the fit before riding:

  • The helmet should sit level on your head, covering your forehead roughly one to two finger-widths above your eyebrows.
  • Tighten the retention system until the helmet does not shift when you shake your head.
  • Buckle the chin strap so that you can fit one or two fingers between the strap and your chin.
  • Open your mouth wide. You should feel the pads press gently against your head.

If the helmet rocks back and forth or slides over your eyes, the size is wrong even if the measurement seemed correct. For a step-by-step process that covers adjusting the fit, read How to Size a Bike Helmet Correctly: A Step-by-Step Fit Guide.

Common Mistakes

  • Measuring over a hat or thick hair, which adds several millimeters and pushes you up a size.
  • Using a rigid tape or a string measured against a ruler, which often introduces error.
  • Assuming your size from another brand applies to the one you are buying.
  • Ignoring the helmet’s internal padding, which can be replaced to fine-tune fit.
  • Skipping the fit check after purchase and riding in an unsafe helmet.
  • Soft measuring tape: A flexible tailor’s tape follows the curve of your head and gives a more accurate circumference reading than a rigid option. View on Amazon
  • Replacement comfort pads: Some riders use sized pad kits to adjust fit when a helmet is between sizes. View on Amazon

FAQ

Should I measure my head with hair up or down?

Measure with your hair as it will be when you ride, but keep it flat and avoid bulky styles. Hair piled high or tied tightly can throw off the reading by a centimeter or more.

How often should I re-measure my head?

Adult head size is generally stable, so one careful measurement is usually enough. Children grow quickly, so re-measure them every few months or before each season.

What if my measurement is between two sizes?

Try both sizes if possible and choose the one that sits level with no pressure points. Many fit experts suggest the smaller size if the helmet has adjustable retention, since the system can take up extra room.

Conclusion

Measuring your head takes only a soft tape and a minute of care. Match the reading to the brand’s own size chart, then confirm the fit on the helmet itself. If you have a medical condition or concerns about head shape, consult a qualified fitter or professional before choosing a helmet.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our bike helmets & cycling safety guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Bike Helmet Snow.