We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Sigma Wireless Bike Computer Not Working: 7 Fixes to Try First

Sigma wireless bike computer not working? Fix pairing, batteries, sensor range and interference with these practical steps before your next ride.

Updated November 2026

When a Sigma wireless bike computer not working problem shows up, it is usually a pairing, battery or signal issue rather than a broken unit. This guide walks you through the checks in the order that solves most problems, so you can get back to accurate speed, cadence and distance readings. Work through the steps in sequence and stop when the display behaves normally.

Check the Batteries in the Computer and Sensors

Low batteries cause more wireless dropouts than almost anything else. Start by replacing the battery in the computer, then in each sensor (speed, cadence or heart rate, depending on your setup). Sigma sensors commonly use coin-cell batteries, and manufacturers specify the exact cell type in the owner’s manual, so check the label on your sensor before buying a replacement. A sensor with a weak battery may still transmit intermittently, which looks like a random failure.

Shopping for one? See our guide: Rockbros M1 Wireless Bike Computer vs Garmin Edge 130: Which Should You Choose?.

Re-Pair the Sensors With the Computer

If the computer shows no data or reads zero, the sensors may have lost their link. Follow the pairing procedure in your model’s manual, which typically involves entering the sensor pairing menu on the computer and then spinning the wheel or pedaling to wake the sensor. Keep the sensor within about one meter of the computer during pairing. Once the sensor shows as connected, confirm live data before you ride.

Check Wheel Magnet and Sensor Alignment

Speed and cadence sensors read a magnet passing a small pickup. If the magnet is loose, bent or too far from the sensor, the signal will drop out. Confirm the following:

  1. The magnet is firmly attached to a spoke (speed) or crank arm (cadence).
  2. The sensor sits within the gap the manufacturer specifies, usually a few millimeters.
  3. The sensor is not mounted on a bent or flexing bracket.
  4. The magnet passes directly in front of the sensor face when the wheel turns.

Rule Out Interference and Range Problems

Wireless sensors use radio signals that can be disrupted by other devices. Move away from gym equipment, power meters from other brands, or a second bike computer running nearby. Also keep the computer on the same side of the bike as the sensors when possible, since metal frames and bodies can block signal. If readings improve when you change position, range or interference is the likely cause.

Reset the Computer if Problems Persist

If the computer freezes, shows garbled numbers or ignores sensors entirely, a reset often clears the fault. Consult the reset instructions in your manual, since the method differs between Sigma models. Note that a reset may erase saved settings, so you may need to reconfigure wheel size and other values afterward. If the unit still fails after a reset, contact Sigma support or an authorized dealer.

Tools and Checks You Will Need

  • Replacement coin-cell batteries matching your sensors and computer
  • Your model’s owner’s manual, for pairing and reset steps
  • A small screwdriver or tool to adjust sensor position
  • A clean cloth to remove dirt from magnets and sensor faces

Common Mistakes

  • Replacing only the computer battery while leaving weak sensor batteries in place.
  • Pairing sensors while far away from the computer, which can cause failed connections.
  • Assuming a dead sensor when the real problem is a loose or misaligned magnet.
  • Skipping the wheel size setting, which makes speed and distance look wrong even when the signal is fine.

A spare set of batteries for your computer and sensors is the most useful item to keep on hand, since battery failure is the most common cause of dropouts. A small multi-tool helps when you need to adjust sensor brackets on the trail. A replacement speed or cadence magnet is also worth carrying if your current one is loose or damaged.

View on Amazon

View on Amazon

FAQ

Why does my Sigma wireless bike computer show zero speed?

The most common reason is that the speed sensor is not detecting the wheel magnet, either because the sensor battery is low or the magnet is out of alignment. Check the sensor battery and confirm the magnet passes directly in front of the sensor when the wheel turns.

How do I know if the sensor or the computer has failed?

Try the sensor with a different computer if you have access to one, or check whether the computer reads other sensors correctly. If only one sensor fails across all attempts, the sensor is the likely fault.

Will resetting my Sigma computer delete my data?

A reset can erase saved settings such as wheel size and user profiles, though ride data may be stored separately depending on the model. Check your manual before resetting, and sync or back up any rides you want to keep.

Conclusion

Most Sigma wireless bike computer problems come down to batteries, pairing or magnet alignment, and you can check all three in a few minutes. Work through the steps in order and rule out interference before assuming hardware failure. If the unit still does not respond after a reset, contact Sigma support or a qualified bike shop for help.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our bike helmets & cycling safety guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Bike Helmet Snow.