We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Set Sigma Bike Computer: A Step-by-Step Guide for Beginners

Learn how to set up a Sigma bike computer step by step, from wheel size and units to sensors and profiles, so your speed and distance readings are accurate.

Updated November 2026

Setting up a Sigma bike computer takes about ten minutes once you know the order of operations. You will enter your personal data, set your wheel size, pair your speed or cadence sensors, and confirm the display shows accurate numbers before your first ride. Getting the wheel size right matters most, because every distance and speed reading depends on it.

Before You Start: Gather What You Need

Have the following ready so you do not have to stop partway through setup:

Shopping for one? See our guide: Sigma Bike Computer 1200 Manual (2026): Which Should You Choose?.

  • The computer, its mounting bracket and the charging cable
  • Your bike, with the rear wheel or front wheel that carries the speed sensor
  • A tape measure, if you want to check wheel circumference by hand
  • The printed manual or the model-specific instructions from Sigma

Charge the unit fully first. Some functions, including Bluetooth pairing, behave unpredictably on a low battery.

Step 1: Enter Your Personal and Unit Settings

  1. Power on the computer and hold the mode or menu button until the settings menu opens.
  2. Choose your language, time format and units (kilometers or miles).
  3. Enter your weight, height, age and gender if the model asks for them. These feed calorie and training estimates, not speed, so they are less critical.
  4. Save and exit the menu.

Step 2: Set the Correct Wheel Size

Wheel size is the setting most riders get wrong. The computer calculates distance by multiplying wheel circumference by revolutions, so an incorrect value throws off every number on the screen. Sigma uses a wheel-size table that lists common tire sizes with a circumference in millimeters. Find your tire’s marked size on the sidewall, locate the matching entry in the manual, and select it.

If your exact tire is not listed, you can enter a custom circumference. Measure it by marking the tire where it meets the ground, rolling the bike one full revolution in a straight line, and measuring the distance between marks. Keep the tire at your normal riding pressure for an accurate figure. For a deeper look at this step, see Bike Computer 29 Inch Wheel: How to Set the Wheel Size Correctly (2026).

Step 3: Pair Your Sensors

Most Sigma computers use either wired connections or ANT+ and Bluetooth wireless sensors. Pairing usually follows this pattern:

  1. Open the sensor menu on the computer and choose “Add sensor.”
  2. Spin the wheel or pedal crank, or activate the sensor as the manual describes, so it wakes up.
  3. Wait for the computer to confirm the connection. Keep the sensor within about one meter during pairing.
  4. Test by spinning the wheel. Speed should register within a few seconds.

If a sensor will not pair, reset it, move away from other cycling electronics and try again. Cadence sensors are set up the same way; the process is covered in Cateye Bike Computer Cadence: How to Set It Up and Read It (Step-by-Step), which is useful for understanding how cadence fits into the same workflow.

Step 4: Create a Profile and Confirm the Readings

If you ride more than one bike, create a separate profile for each one. Each profile should hold its own wheel size and sensor pairings, so you do not have to reset the computer when you switch bikes.

Before heading out, roll the bike a short distance. Check that speed responds, that the distance counter increases, and that the display updates smoothly. A quick test on a driveway catches most errors.

Common Mistakes

  • Using the tire size printed on the sidewall without checking it against the manual’s table
  • Measuring wheel circumference with a deflated or under-inflated tire
  • Forgetting to switch units after a firmware or profile change
  • Pairing sensors while another nearby bike computer is also searching
  • Skipping the test ride and discovering a wrong setting halfway through a long route

A stable mount keeps the computer readable and reduces vibration-related glitches on rough roads. View on Amazon

A spare sensor battery lets you troubleshoot quickly if a reading drops out mid-ride. View on Amazon

FAQ

Why does my Sigma show the wrong distance?

The most common cause is an incorrect wheel size. Check the tire size against the manual’s table, or measure your custom circumference again with the tire at normal pressure.

Do I need to re-pair sensors every time I ride?

Usually not. Once paired, sensors reconnect automatically when they are in range, although a dead sensor battery will stop the connection.

Where can I find the manual for my specific Sigma model?

Sigma publishes manuals on its official website, organized by model name. Check the product name printed on the unit, then search the support section for that exact model.

Conclusion

Once you enter your units, set the correct wheel size, pair your sensors and run a short test, your Sigma should give reliable readings. Repeat the wheel-size check whenever you change tires. A few minutes of setup at the start saves you from inaccurate data on every ride after.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our bike helmets & cycling safety guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Bike Helmet Snow.