We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Bike Phone Mount DIY: Build a Safe Handlebar Holder in 6 Steps

Learn how to build a bike phone mount DIY with simple materials. Follow these steps for a secure, vibration-resistant handlebar holder you can trust on every ri

Updated November 2026

A bike phone mount DIY project lets you hold your phone securely on your handlebars using a few basic materials and about an hour of work. This guide walks through choosing materials, attaching a holder, and testing the mount so your phone stays put over bumps. The result is a mount that keeps your screen visible without blocking your brake levers or bell.

Choose Your Materials and Mounting Position

Most homemade mounts use a rubber or silicone strap, a rigid holder plate, and a spacer or padding to protect the phone and handlebar. Before buying anything, measure your handlebar diameter, which is typically 22.2 mm for road bars and 31.8 mm for many flat bars. Position the mount where you can read the screen at a glance, usually centered between your hands and clear of cables, brake lines and your bell.

Shopping for one? See our guide: 3 Best Phone Mounts for Mountain Bike Picks for Trail Riders (2026).

Build and Attach the Mount

Follow these steps to assemble and install the mount:

  1. Cut a strip of closed-cell foam or a rubber inner tube to fit around the handlebar, leaving about 10 mm of overlap.
  2. Attach a rigid holder plate, such as a cut piece of thin aluminum or a sturdy plastic bracket, to the foam with strong adhesive or small rivets.
  3. Wrap the foam around the handlebar and secure it with two rubber or nylon straps, pulling each one snug.
  4. Test the holder by pressing firmly in all directions. It should not rotate or slide.
  5. Add a phone cradle, using a stick-on mount plate or a clamp, and confirm the phone sits flat with its camera and buttons accessible.

Test for Vibration, Clearance and Security

A mount that looks solid can still shake loose on rough pavement. Ride a short loop on the roughest surface you normally use, then stop and check the strap tension, the adhesive bond and the phone’s position. Confirm that the mount does not touch your brake levers, shifter cables, or the steerer when you turn the bars fully left and right. If the phone rattles, add padding between the cradle and the holder plate.

Protect Your Phone From Heat and Rain

Phones can overheat in direct sunlight, and many models will throttle or shut down when hot. Use a shaded position where possible and remove the phone when parking in the sun. A cover with a sealed port cover helps keep moisture out during wet rides.

Common Mistakes to Avoid

  • Mounting the phone too low, which blocks your view of the road.
  • Using thin elastic bands that stretch and slip over time.
  • Placing the mount where it interferes with brake or shifter operation.
  • Skipping a post-ride check of strap tension and adhesive.
  • Relying on a homemade mount for heavy phones or cases without testing the load first.

A quality stem or bar clamp makes DIY installation easier and more stable. View on Amazon

Closed-cell foam padding protects both your bar and your phone from rubbing. View on Amazon

Heavy-duty rubber straps resist stretching better than elastic bands. View on Amazon

FAQ

Can a DIY bike phone mount damage my handlebars?

It can if the holder is over-tightened or lacks padding. Always use foam or rubber between the strap and the bar, and avoid tightening past the point where the strap stops compressing.

Is a homemade phone mount safe for commuting?

It can be, provided it is secure, clear of controls and checked before each ride. Riders on busy streets should also keep the phone’s screen brightness low to reduce distraction, and should consider a dedicated bike computer for navigation. Consult a local bike shop if you are unsure about your setup.

How do I keep my phone from falling off?

Use a mount with a locking clip or strong magnet, and check the connection before each ride. Adding a secondary strap as a backup helps on rough roads.

Conclusion

A well-built bike phone mount DIY project gives you a secure, readable screen for navigation and tracking. Choose materials that resist vibration, place the mount where it does not block your controls, and test it on a short ride before relying on it. Recheck the straps and adhesive regularly, and replace worn parts promptly.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our bike helmets & cycling safety guides, checking product details against manufacturer specifications and owner feedback.

About the author

Ethan Brooks
Ethan Brooks

Ethan Brooks writes reviews and buying guides for Bike Helmet Snow.