How to Turn Lights On Lectric XP Bike: Step-by-Step Guide (2026)
Learn how to turn lights on Lectric XP bike with a simple step-by-step guide covering the controls, checks and common fixes so you ride visible.
Updated November 2026
To turn lights on a Lectric XP bike, you press and hold the correct control on the display or handlebar switch until the headlight and taillight respond. This guide walks through the basic sequence, how to confirm the lights are working, and what to check when they stay dark. Keeping your lights on is one of the simplest ways to stay visible in traffic, especially at dawn, dusk and night.
Locate the Light Control
Start by finding where the lights are controlled on your bike. On most Lectric XP models, the main controls sit on the left side of the handlebar and feed into the display. Before pressing anything, make sure the bike is powered on so the display is active. If the display is off, the lights will not respond.
Shopping for one? See our guide: 6 Best Mountain Bike Lights for Helmet for Night Trail Riding (2026).
Look for a dedicated light button or an icon on the display that looks like a headlight. Lectric bikes are designed with one main control cluster, so you should not need to hunt far. If you are unsure of the layout for your exact model year, check the owner’s manual that came with the bike or the manufacturer’s support pages.
Turn the Lights On Step by Step
Follow these steps in order:
- Switch the bike on using the main power button and wait for the display to fully load.
- Locate the light button or light icon on the handlebar control or display.
- Press the button once and watch the display. A light indicator should appear.
- If nothing changes, press and hold the button for two to three seconds. Some settings require a longer hold to activate.
- Confirm the headlight is on by checking the front of the bike in a dim spot, and check the taillight by looking behind you or using a reflection.
When the lights are on, the display should show a visible status indicator. If you only see the indicator but the lamps look dim, the battery may be low.
Check Battery Level First
Lights draw power from the same battery that drives the motor. A low charge can cause the lights to flicker, dim or refuse to switch on. Before troubleshooting anything else, check the battery indicator on the display. If it shows a low charge, charge the bike fully and try again.
Troubleshoot Lights That Stay Off
If the lights do not come on after following the steps above, work through these checks in order:
- Confirm the display is powered on and not in a sleep or standby state.
- Check the battery level and charge the bike if it is low.
- Inspect the light connectors near the headlight and taillight for loose or disconnected wires.
- Look for a bulb or LED lamp that may have failed, which is often visible as one light working and the other not.
- Restart the bike by turning it fully off, waiting about 30 seconds, and powering it back on.
If the lights still will not respond after these checks, the wiring or controller may need professional inspection. Contact Lectric support or a qualified bike shop rather than opening electrical housings yourself.
Common Mistakes
- Pressing the light button while the bike is still powering up, which can leave the lights in an unexpected state.
- Assuming the lights are on because the indicator shows, without checking the actual lamps.
- Ignoring low battery warnings, which can cut power to the lights during a ride.
- Riding at night with only the front light and no rear light.
- Pulling on or bending wires near the light housings while troubleshooting.
Recommended Gear
A supplemental rear light adds visibility if the built-in taillight is dim or hard to see from the side. Look for a rear light that mounts to the seat post or rack. View on Amazon
A small bike multitool helps when you need to check connections or tighten a mount that has loosened over time. View on Amazon
Related Reading
If you want to add signaling or mount accessory lights, see Bike Turn Signal Lights: How to Choose, Mount and Use Them Safely (2026) for guidance on safe placement. For front lighting options, Fork Mounted Bike Lights: How to Choose and Mount Them Safely (2026) covers mounting details.
FAQ
Why won’t my Lectric XP lights turn on?
The most common cause is a low battery or a display that is not fully powered on. Charge the bike, restart it, and try the light button again.
Do I need to hold the light button or just press it?
Try a single press first. If nothing changes, hold the button for two to three seconds, since some settings require a longer press.
Should I ride with lights on during the day?
Using lights during daytime can improve visibility to drivers, especially in overcast weather or heavy traffic. Keep them on whenever visibility is reduced.
Conclusion
Turning on your Lectric XP lights comes down to powering the bike on, pressing the light control, and confirming the lamps respond. Keep the battery charged and check the connections whenever lights fail. Always make sure both front and rear lights are working before you ride in low light.
Related reading
- Bike Turning Signal Lights: How to Choose, Mount and Use Them Safely
- Bike Lights Powered by Pedaling: How They Work and How to Choose One (2026)
Ready to choose one?
